|
Hammer Crusher
The hammer crushers are basically secondary crushers, Their robust and sturdy design makes them well-suited for primary crushing for materials which have been quarried by ripping or similar fragmenting methods as well as for gypsum and raw coal. It can be divided into hammer crusher, and ring hammer crusher.
Hammer crusher is suitable for mid-hard and light erosive materials, whose pressure resistance strength is no more than 100Mpa and humidity lower than 15%, such as coal, salt, chalk, gypsum, blocks, limestone, etc.
Operation Principle Of Hammer Crusher:
The main working part of hammer crusher is rotors with hammer. The rotors consist of main shaft, disk, pin shaft and hammers. The motor drives the rotors to rotate quickly in the crushing cavity. Raw materials enter the crusher through the feed opening and are stricken, impacted, cut and ground by the high-speed hammer to small size. There is a screening plate under the rotor, so that materials with size smaller than the screen mesh will be screened out and others are left to be further hammered and ground until reach the standard size. The size of the final product can be adjusted by changing the screening plate. The gap between the rotors and the screening plate can also be adjusted according to different requirement.
Hammer Crusher Features:
Our PC hammer crusher features in its simple structure, high reduction ration, high efficiency, ect.. |
|
| |
| Technical Data Of The Hammer Crusher: |
| Sort |
NO. |
Model |
Feeding size (mm) |
Output size
(mm) |
Capacity (t/h) |
Moter |
Weight (t) |
| Model |
KW |
| Hammer crusher |
1 |
PCφ400×300 |
≤200 |
≤25 |
8-15 |
Y160M-4 |
11 |
0.8 |
| 2 |
PCφ500×350 |
≤210 |
≤25 |
12-20 |
Y180M-4 |
18.5 |
1.2 |
| 3 |
PCφ600×400 |
≤250 |
≤30 |
15-30 |
Y180L-4 |
22 |
1.5 |
| 4 |
PCAφ800×600 |
≤300 |
≤30 |
25-50 |
Y250M-4 |
55 |
2 |
| 5 |
PCφ800×600 |
≤200 |
≤25 |
20-50 |
Y280M-6 |
55 |
2.6 |
| 6 |
PCφ1000×800 |
≤300 |
≤35 |
30-65 |
Y315S-6 |
75 |
4 |
| 7 |
PCφ1000×1000 |
≤300 |
≤35 |
45-80 |
Y315M-6 |
90 |
6 |
| Ring hammer crusher |
1 |
PCH0808 |
≤200 |
≤15 |
18-37 |
Y132M-6 |
45 |
5.3 |
| 2 |
PCH1010 |
≤300 |
≤15 |
30-42 |
Y280S-6 |
90 |
7.2 |
| 3 |
PCH1016 |
≤300 |
≤30 |
250-300 |
Y315M-6 |
155-220 |
12 |
| 4 |
PCH1212 |
≤300 |
≤30 |
260-320 |
Y315M-6 |
132-280 |
13.6 |
| 5 |
PCH1216 |
≤350 |
≤30 |
380-500 |
Y315M-6 |
220-355 |
19.1 |
|
| Note: If there is change of the Hammer crusher specification, it subjects to the newest products' specifications. |
| |
|
|
